Used to loosen and tighten drain fittings and supply lines. We carry multiple sizes to handle any connection under the sink.
Sink installation Cleburne TX done right the first time
Sink installation Cleburne TX homeowners can count on starts with a proper measurement, a watertight seal, and supply lines that won't drip.
Serving cleburne and nearby areas.
How big is the job?
Upgrade
New sink type, faucet, or disposal added.
- 1. Simple swap Same-size drop-in sink, existing plumbing in good shape.
- 2. Upgrade New sink type, faucet, or disposal added.
- 3. Full remodel Countertop cut, new plumbing lines, multiple fixtures.
Drag the needle to compareTouch and drag the needle
- 30Services from one local team
- 20Areas served around cleburne
- Measure twiceWe check the opening and parts before starting.
- Test every jointWe run water and check for leaks before leaving.
What our sink installation service includes
Every sink installation includes the essentials to get your sink working properly.

Work order
Sink Installation- Old sink removal and disposal: We disconnect the old sink, remove it, and haul it away. If you want to keep it, just let us know. We protect your countertop and floor during removal.
- New sink setting and sealing: We set your new sink with the correct sealant or gasket for the material. For undermount sinks, we use mounting clips and ensure a flush fit. We check the alignment before securing it.
- Faucet and drain connection: We connect the faucet, drain assembly, and P-trap. We install new supply lines and use Teflon tape on threaded fittings. We also connect the disposal if you have one.
- Leak test and cleanup: We fill the sink, let it drain, and check every connection with a dry paper towel. We run the disposal and check the flange. Once everything is dry, we clean the work area and show you the finished job.
What the first visit covers
First visit
We measure the opening, check shutoff valves and drain lines, and confirm the new sink will fit.
Sink installation for Cleburne homes
We install kitchen and bathroom sinks in houses across Cleburne.
Kitchen sink replacement
Drop-in or undermount, with faucet and disposal.
Bathroom vanity sink
New sink and faucet for your vanity top.
Farmhouse sink install
We cut the counter and set the apron-front sink.
Customer-supplied sink
You buy it, we install it and test for leaks.

Sink installation for Cleburne businesses
We install sinks in commercial kitchens, offices, and retail spaces.
Commercial kitchen sinks
Stainless steel and multiple-compartment sinks.
Office breakroom sinks
Standard sinks with faucets and disposals.
Retail and salon sinks
Vanity and utility sinks for customer areas.
Sink installation Cleburne TX: what the job actually involves
A sink that's installed correctly protects your cabinets and saves water. We measure, seal, and test every connection so you don't have to worry about leaks.
Sink installation Cleburne TX is the process of removing an old sink, prepping the countertop opening, setting the new basin, and connecting the drain, supply lines, and faucet so everything drains and seals correctly. It sounds simple until you're under a cabinet with a pipe wrench fighting corroded fittings. We handle drop-in, undermount, and farmhouse sinks in kitchens, plus vanity and pedestal sinks in bathrooms. Every install includes new supply lines, a fresh wax ring or silicone seal as needed, and a leak test before we pack up.
Most Cleburne homes were built between the 1950s and 1990s, and original cast iron or PVC pipe under the cabinet has often been patched more than once. That's why a sink install Cleburne TX often turns into a small repair job: a shutoff valve that won't close, a P-trap that's cracked, or a disposal flange that's rusted through. We check those parts before we start so you're not calling us back a week later. If you've been searching for sink installation near me Cleburne TX, we're local and we carry the common parts on the truck.

- What it is
- Removing an old sink and installing a new one.
- When it helps
- Cracked sink, remodel, or upgrading fixtures.
- What you get
- A watertight sink that drains properly.
How our sink installation process works
We keep it simple: you tell us what you want, we measure and quote, then we install and test.
Tools and methods we use for sink installation
Each method answers a different question. Together they leave very little to guess.
Cuts copper and PEX supply lines cleanly. A clean cut ensures a proper seal and prevents leaks at the fitting.
Used to secure PEX fittings when we replace supply lines. It creates a permanent, leak-free connection.
For copper pipe repairs or modifications. We use it when we need to solder a new fitting or repair a damaged section.
Helps us find hidden leaks under the sink or in the wall. We use it to confirm the source before we start cutting.
When to schedule a sink installation
You're remodeling your kitchen and want a new farmhouse sink.
We measure the cabinet opening, cut the countertop if needed, and install the farmhouse sink with a new faucet and disposal.
HomesYour bathroom vanity sink is cracked and you want to replace it.
We remove the old sink, install a new vanity top and sink, and connect the faucet and drain.
HomesYou bought a new sink online but need a professional to install it.
We install customer-supplied sinks. Just have the sink and all parts ready. We'll check the fit, install it, and test for leaks.
HomesYour old sink is leaking and you need it replaced quickly.
We offer same-day sink installation when possible.
Homes
How sink installation works in Cleburne
Cleburne homes range from early 1900s builds near the Historic District to newer construction around Lake Pat Cleburne. Older homes often have cast iron drains and galvanized supply lines that can be brittle.
Downtown Cleburne
Many historic homes here have original cast iron drains. We check for cracks and root intrusion before installing a new sink.
Lake Pat Cleburne
Newer homes often have PEX supply lines. We match fittings and ensure the water pressure is balanced.
Sunset Heights
Mid-century homes with galvanized pipes. We often replace corroded shutoff valves during a sink install.

- Downtown Cleburne
- Lake Pat Cleburne
- Sunset Heights
- North Cleburne
From problem to finished result.
Slide to compare the photo with an illustrative inspection view. It is generated from the photo, not a measurement.
PhotoCracked kitchen sink replaced in one visit
Before: A homeowner in Downtown Cleburne had a cast iron sink with a crack that leaked into the cabinet. The cabinet floor was water-stained, and the shutoff valves were frozen.
After: We removed the old sink, replaced both shutoff valves, installed a new stainless steel drop-in sink with a new faucet, and sealed the cabinet floor. The job took about 3 hours, and the leak was gone.
Undermount sink reattached in Sunset Heights
Before: An undermount sink in Sunset Heights had separated from the countertop, leaving a gap that allowed water to seep into the cabinet. The adhesive had failed.
After: We removed the sink, cleaned the old adhesive, and reinstalled it with new mounting clips and silicone. We also replaced the P-trap. The sink is now flush and watertight.
Bathroom vanity sink upgrade in North Cleburne
Before: A North Cleburne homeowner had a dated bathroom vanity with a cracked sink and a dripping faucet. The supply lines were corroded.
After: We installed a new vanity top with an undermount sink, a new faucet, and new supply lines. We also replaced the shutoff valves. The job took 4 hours and the drip stopped.
Common sink problems we solve in Cleburne
Sinks fail in predictable ways. Here are the issues we see most often and how we fix them.
Cracked or chipped sink basin
A cracked sink can leak water into the cabinet, causing wood rot and mold. Even a small chip can spread and lead to a bigger break.
Leaking drain or P-trap
A leaking drain can warp the cabinet floor and create a breeding ground for mold. It also wastes water and can damage stored items.
Corroded shutoff valves
Old shutoff valves can seize or leak when you try to turn them off. That turns a simple sink replacement into a water emergency.
Undermount sink falling away from counter
Undermount sinks can separate from the countertop if the adhesive fails. That leaves a gap where water can get in and damage the cabinet.
Why a proper sink installation matters
A sink that's installed correctly protects your cabinets, your countertop, and your water bill. Here's what you get when the job is done right.
No leaks, no callbacks
We pressure-test every supply line and drain connection before we leave.
Correct cut, clean countertop
Undermount and drop-in sinks need different cutout dimensions, and getting it wrong means a cracked countertop.
Code-compliant drain and vent
Texas follows the Uniform Plumbing Code, and that means your sink drain needs a proper P-trap and an air admittance valve or vent connection.
Disposal and faucet done together
If you're replacing the sink, it's the right time to install a new faucet and garbage disposal.
What you receive
Clear records you can keep and share.
Written estimate
Price before we start, no surprises.
Install photos
Before and after pictures of the work.
Parts list
Record of any new valves or lines installed.
16 years of sink installation experience in Cleburne
Cleburne Trailcrest Plumbing has been installing sinks since 2010.

Shutoff valve condition
We turn the valve to check if it closes fully and doesn't leak.
Drain line flow
We run water and watch how fast it drains to spot clogs.
Cabinet floor
We check for water stains or soft spots that mean past leaks.
Is your Cleburne address covered?
Type your ZIP code or town to check. If you're not listed, call and ask.
cleburne ZIP codes
- 76033
- 76031
Towns we serve.
Based in cleburne and covering the places around it. Pick one for local details.
What Cleburne homeowners say
We had a cracked kitchen sink that was leaking into the cabinet. Cleburne Trailcrest came out the same day, replaced the sink and the disposal, and even fixed a corroded shutoff valve. The price was exactly what they quoted. No mess left behind. I'd use them again for sure.
I bought an undermount sink online and needed it installed. They measured, cut the countertop, and had it done in about three hours. They showed me the old P-trap was cracked and replaced it. Everything drains perfectly now. Fair price and good communication.
Our bathroom vanity sink was original to the house and looked terrible. They installed a new sink and faucet, and also replaced the supply lines. The technician was polite and cleaned up after himself. It's nice to find a local company that does what they say.
Frequently Asked Questions
Short answers for the first few minutes. The team can cover the rest.
Describe what you are seeing and we will point you to the right next step.
(682) 468-2111We give you a written quote before we start, so you know the number upfront.
A typical sink replacement takes 2 to 4 hours from start to finish. That includes removing the old sink, installing the new one, connecting the faucet and drain, and testing for leaks. If we're cutting a new countertop opening or running new supply lines, plan on 4 to 6 hours. We schedule a window and keep you updated.
Yes, we install customer-supplied sinks all the time. Just have the sink, faucet, and any mounting hardware on site when we arrive. We'll inspect the parts and let you know if anything is missing or incompatible before we start. There's no extra charge for using your own sink, and the labor rate stays the same.
We install both kitchen and bathroom sinks, including drop-in, undermount, farmhouse, vanity, and pedestal styles. For kitchens, we also handle garbage disposals, dishwashers, and faucet replacements. For bathrooms, we can replace the vanity top and sink together. If you're not sure what will fit, call us and we'll help you measure.
Ready for sink installation Cleburne TX? Call today
(682) 468-2111Call now for a free estimate and same-day availability. We'll bring the parts and get it done right.
Contact Cleburne Trailcrest Plumbing
Call us at (682) 468-2111 or email [email protected]. We answer the phone Monday through Friday, 8 a.m. to 6 p.m., and we run emergency calls after hours. If you leave a message, we call back the same day. Tell us what you're seeing and we'll tell you what it likely is and when we can get there.







