Repair TipsLocal Guides

Why does my faucet drip and how to stop it

A dripping faucet is usually a worn washer, cartridge, or seat. Learn why it happens and how to stop it with faucet drip repair in Cleburne TX.

9 min read
A close-up of a rustic outdoor faucet dripping water against a natural, textured background, symbolizing scarcity.

A dripping faucet is almost always caused by a worn-out washer, cartridge, or valve seat inside the fixture. The fix is usually a simple repair - replacing that one small part stops the drip and saves thousands of gallons of water a year. In this post, we'll explain exactly why your faucet drips and walk you through how to stop it, with tips specific to homes here in Cleburne, Texas.

We're Cleburne Trailcrest Plumbing, and we've fixed more dripping faucets than we can count. If you'd rather skip the DIY and have a pro handle it, we offer faucet repair Cleburne TX with upfront pricing. But if you're handy, read on - you can often fix this yourself in under an hour.

The Usual Suspects: Why Faucets Drip

Faucet drip repair in Cleburne TX starts with understanding the mechanics. Every faucet has a valve that controls water flow. When you turn the handle, a rubber or ceramic component presses against a seat to seal off the water. Over time, minerals in the water - and Cleburne's water is moderately hard, at around 8 to 10 grains per gallon - wear down that seal. Once the seal fails, water slips past and drips out the spout.

The specific culprit depends on your faucet type:

  • Compression faucets (common in older Cleburne homes): A rubber washer at the end of the stem wears out. This is the classic drip - one drop every few seconds.
  • Ball-type faucets (popular in the 80s and 90s): The ball, springs, or seals inside the handle degrade.
  • Cartridge faucets (most modern fixtures): The cartridge itself cracks or accumulates mineral deposits.
  • Ceramic disc faucets (high-end models): Sediment scratches the ceramic discs, allowing water to seep through.

In Cleburne, we also see a lot of drip issues caused by high water pressure. The city's water pressure often runs 60 to 80 psi, and anything over 80 psi stresses faucet seals. If your faucet drips soon after installation, check your home's pressure regulator - it might be failing.

Another local factor: temperature swings. North Texas sees 100°F summers and occasional freezes. That expansion and contraction can loosen valve seats over time. If your faucet drips more in summer or after a cold snap, that's likely why.

How to Stop a Dripping Faucet: A Step-by-Step Guide

You can stop most faucet drips yourself with basic tools and a replacement kit that costs $10 to $25. Here's the process we use on service calls, simplified for a homeowner.

1. Identify Your Faucet Brand and Model

Look under the sink or on the faucet base for a brand name - Moen, Delta, Kohler, American Standard. Take a photo of the faucet and the model number if you can find it. This ensures you buy the right replacement parts. Most hardware stores in Cleburne, like the local Ace or Lowe's, stock common cartridges and washers.

2. Shut Off the Water Supply

Turn off the two shut-off valves under the sink (one for hot, one for cold). If they're stuck or missing, shut off the main water valve to the house. Open the faucet to release pressure and confirm the water is off.

3. Disassemble the Faucet Handle

Pry off the decorative cap on top of the handle (use a flathead screwdriver or your fingernail). Remove the screw underneath, then pull the handle straight up. You may need a faucet handle puller if it's stuck - these cost about $10.

4. Remove and Inspect the Valve Components

Depending on your faucet type, you'll see a stem with a washer, a ball, a cartridge, or ceramic discs. Pull them out and inspect for wear, cracks, or mineral buildup. A white, crusty deposit is a sure sign of hard water damage.

5. Replace the Worn Parts

Take the old parts to the store and match them exactly. For compression faucets, replace the washer and the O-ring. For cartridge faucets, swap in a new cartridge. For ball faucets, replace the springs and seals. Coat new rubber parts with plumber's grease to help them seat properly.

6. Reassemble and Test

Put everything back together in reverse order. Turn the water supply back on slowly, then open the faucet and let it run for a minute. If the drip is gone, you're done. If it still drips, the valve seat may be damaged - that's a job for a pro.

If you'd rather not tackle this yourself, our plumbing repairs Cleburne TX team handles faucet drip repair every day. We carry common parts on our trucks and can usually fix it in one visit.

When to Call a Professional

Some faucet drips are not a DIY fix. Call a professional if:

  • The drip continues after you've replaced the obvious parts.
  • You see water pooling under the sink or on the cabinet floor.
  • The faucet is a high-end or obscure brand you can't find parts for.
  • You have to shut off the main water valve because the under-sink valves are broken.
  • The faucet is more than 15 years old and parts are discontinued.

We also recommend calling us if your faucet drips only when the hot water is on - that can signal a problem with your water heater's pressure relief or a cross-connection issue. Our water heater repair Cleburne TX team can diagnose that quickly.

At Cleburne Trailcrest Plumbing, we diagnose the issue, give you a flat-rate price before we start, and fix it right the first time. No guesswork, no surprise charges.

Common Mistakes to Avoid

We see these mistakes often when homeowners attempt their own faucet drip repair in Cleburne TX. Avoid them to save time and frustration.

  • Forcing a stuck handle. You'll crack the finish or break the valve. Use a handle puller.
  • Over-tightening the packing nut. This crushes the washer and causes a worse leak. Tighten snug, then a quarter-turn more.
  • Using the wrong replacement parts. A washer that's slightly too small will fail in weeks. Match the brand and model exactly.
  • Ignoring the valve seat. If the seat is rough, a new washer will wear out fast. Resurface or replace the seat.
  • Not checking water pressure. If your home's pressure is over 80 psi, new parts will fail prematurely. Install a pressure-reducing valve.

One more: don't ignore a drip because it seems minor. A faucet dripping once per second wastes over 3,000 gallons of water per year - that's about $30 to $50 on your Cleburne water bill, plus the wear on your fixture.

How Much Does Faucet Drip Repair Cost in Cleburne?

Typical 2026 pricing for faucet drip repair in Cleburne ranges from $150 to $350, depending on the faucet type and parts needed. A simple washer replacement might be on the low end; a cartridge or ceramic disc replacement on a high-end faucet could be higher. If you need a new faucet installed, expect $200 to $500 for the labor and materials.

We charge a flat service call fee that includes diagnosis, and we credit that fee toward the repair if you hire us. Call us for an exact quote - we'll give you a straight answer over the phone.

If your faucet is part of a larger issue - like low water pressure throughout the house - you may need leak detection Cleburne TX to find hidden leaks. We can handle that too.

Frequently Asked Questions

Why does my faucet drip in Cleburne?

Cleburne's moderately hard water (8-10 grains per gallon) wears down washers and cartridges faster than in softer-water areas. High water pressure (often 60-80 psi) also stresses seals. Both are common causes of drips here.

How do I stop my faucet from dripping in Cleburne TX?

Shut off the water, disassemble the handle, and replace the worn washer, cartridge, or seals. If the valve seat is damaged, resurface or replace it. If you're not comfortable doing this, call a plumber - we fix drips in under an hour.

Can a dripping faucet be repaired in Cleburne?

Yes, almost always. A dripping faucet is a repairable problem, not a reason to replace the whole fixture. In rare cases where parts are obsolete, we may recommend a new faucet, but that's uncommon.

How much does faucet drip repair cost in Cleburne?

In 2026, expect $150 to $350 for a professional repair, including parts. DIY kits cost $10 to $25. If you need a new faucet installed, add $200 to $500 for labor and materials.

Is a dripping faucet an emergency?

Not usually. But if the drip is accompanied by water under the sink, low water pressure, or a constantly running water heater, call us. Those signs point to a bigger problem that can cause water damage.

Get Help with Plumbing in Cleburne

If you'd rather not spend your weekend under the sink, we're here to help. Cleburne Trailcrest Plumbing provides fast, friendly faucet drip repair and all types of plumbing Cleburne TX services. Call us at (682) 468-2111 to schedule a visit - we'll stop that drip and get your water bill back to normal.

Tagged withfaucet repairdiy plumbingcleburne txwater wastehome maintenance

A few answers before you start.

Short answers for the first few minutes. The team can cover the rest.

Still have a question?

Describe what you are seeing and we will point you to the right next step.

(682) 468-2111

Cleburne's moderately hard water (8-10 grains per gallon) wears down washers and cartridges faster than in softer-water areas. High water pressure (often 60-80 psi) also stresses seals. Both are common causes of drips here.

Shut off the water, disassemble the handle, and replace the worn washer, cartridge, or seals. If the valve seat is damaged, resurface or replace it. If you're not comfortable doing this, call a plumber - we fix drips in under an hour.

Yes, almost always. A dripping faucet is a repairable problem, not a reason to replace the whole fixture. In rare cases where parts are obsolete, we may recommend a new faucet, but that's uncommon.

Not usually. But if the drip is accompanied by water under the sink, low water pressure, or a constantly running water heater, call us. Those signs point to a bigger problem that can cause water damage.

Stop the drip today with plumbing in Cleburne

(682) 468-2111

Our team fixes faucet drips fast, with upfront pricing and no mess. Call Cleburne Trailcrest Plumbing and get your water bill back under control.

Call now(682) 468-2111